Ets-lindgren 3143B BiConiLog Antenna Manuale Utente

Model 3143B BiConiLog™ Antenna User Manual Model 3143B shown in horizontal polarization

10 | Introduction ETS-Lindgren Product Information Bulletin See the ETS-Lindgren Product Information Bulletin included with your shipment for th

Maintenance | 11 2.0 Maintenance Before performing any maintenance, follow the safety information in the ETS-Lindgren Product Information Bul

12 | Maintenance Service Procedures For the steps to return a system or system component to ETS-Lindgren for service, see the Product Informatio

Specifications | 13 3.0 Specifications Electrical Specifications Frequency Range: 26 MHz–1 GHz Input Impedance (Nominal): 50 Ω VSWR (Average):

14 | Specifications This page intentionally left blank.

Assembly Instructions | 15 4.0 Assembly Instructions Before connecting any components, follow the safety information in the ETS-Lindgren Prod

16 | Assembly Instructions Attach Bowtie Elements Photos of bowtie elements used in this section may differ from the bowtie elements for your M

Assembly Instructions | 17 1. For stability, mount the Model 3143B onto a tripod or tower. See Mounting Instructions on page 19 for the steps t

18 | Assembly Instructions This page intentionally left blank.

Mounting Instructions | 19 5.0 Mounting Instructions Before connecting any components, follow the safety information in the ETS-Lindgren Prod

ii | ETS-Lindgren L.P. reserves the right to make changes to any product described herein in order to improve function, design, or for any other reas

20 | Mounting Instructions Using Included Mounting Adapters In addition to the attached mounting bracket and mounting knobs, the Model 3143B shi

Mounting Instructions | 21 To attach the included adapters to the Model 3143B: Model 3143B mounted onto 4-TR using included 100989 Polarizing

22 | Mounting Instructions Using the Stinger to Mount to a Model 2175 MiniMast Do not use the stinger to mount the Model 3143B onto a 4-TR trip

Mounting Instructions | 23 2. Attach the cable to the Type N connector at the end of the stinger. 3. Slide the cable and stinger into the cla

24 | Mounting Instructions 5. Tighten the clamp knobs on the boom to secure the antenna into place.

Mounting Instructions | 25 Additional Mounting Options 4-TR MOUNTING OPTIONS Following are additional options for mounting the Model 3143B onto

26 | Mounting Instructions 7-TR AND MAST MOUNTING OPTIONS The stinger on the Model 3143B enables you to mount to antenna directly to an ETS-Lind

Mounting Instructions | 27 Mast refers to 2070 Series, 2075, and 2175 Antenna Towers. 7-TR refers to 109042, 108983, and 108197 booms:  10904

28 | Mounting Instructions 2X2 BOOM MOUNTING OPTIONS Following are additional options for mounting the Model 3143B onto a 2x2 boom. Contact the

Typical Data | 29 6.0 Typical Data Typical Antenna Factor and Gain Distance for the ANSI 3-meter and 10-meter calibrations is measured from th

| iii Table of Contents Notes, Cautions, and Warnings ... v 1.0 Introduction ...

30 | Typical Data Typical VSWR

Typical Data | 31 Typical Beamwidth

32 | Typical Data Typical Power Requirements HORIZONTAL

Typical Data | 33 VERTICAL

34 | Typical Data This page intentionally left blank.

Warranty | 35 Appendix A: Warranty See the Product Information Bulletin included with your shipment for the complete ETS-Lindgren warranty fo

iv | This page intentionally left blank.

| v Notes, Cautions, and Warnings Note: Denotes helpful information intended to provide tips for better use of the product. Caution: Denotes a haza

vi | This page intentionally left blank.

Introduction | 7 1.0 Introduction The ETS-Lindgren Model 3143B BiConiLog™ Antenna is designed as a dual-purpose antenna that can be used for b

8 | Introduction Model 3143B shown in horizontal polarization The Model 3143B includes a stinger mount; it also includes a mounting bracket and

Introduction | 9 Tripod Options ETS-Lindgren offers the following non-metallic, non-reflective tripods for use at both indoor and outdoor EMC te