Ets-lindgren HI-4416 Numeric EMF Readout Unit Manuale Utente

HI-4416 System Readout User Manual

10 Introduction www.ets-lindgren.com ETS-Lindgren Product Information Bulletin See the ETS-Lindgren Product Information Bulletin included with your s

www.ets-lindgren.com Maintenance 11 2.0 Maintenance Before performing any maintenance, follow the safety information in the ETS-Lindgren Product I

12 Maintenance www.ets-lindgren.com Replacement and Optional Parts ETS-Lindgren may substitute a similar part or new part number with the same funct

www.ets-lindgren.com Specifications 13 3.0 Specifications Electrical Specifications Operating Temperature +10º C to +40º C (+50º F to +104º F) Humi

14 Specifications www.ets-lindgren.com This page intentionally left blank.

www.ets-lindgren.com Pre-Installation Tasks 15 4.0 Pre-Installation Tasks Before connecting any components, follow the safety information in the E

16 Pre-Installation Tasks www.ets-lindgren.com 5. Press the ON/OFF keypad on the front panel of the HI-4416. All segments of the LCD will activate f

www.ets-lindgren.com Operation 17 5.0 Operation Before connecting any components, follow the safety information in the ETS-Lindgren Product Inform

18 Operation www.ets-lindgren.com Once the system readout is turned on, all segments of the LCD will activate for two seconds, the version of softwar

www.ets-lindgren.com Operation 19 Keypad Operation The operation of the HI-4416 System Readout is controlled by membrane switches. To activate a swi

ii www.ets-lindgren.com ETS-Lindgren Inc. reserves the right to make changes to any product described herein in order to improve function, design, or

20 Operation www.ets-lindgren.com Mode Select—Selects one of the four modes of the keypad matrix. For maximum operating flexibility, the HI-4416 uti

www.ets-lindgren.com Operation 21 The maximum value is cleared when the HI-4416 is powered up, when the Max key is released and when the unit of meas

22 Operation www.ets-lindgren.com Clear Data—Clears all readings out of data log memory. To perform this operation, press and hold the Clear Data key

www.ets-lindgren.com Operation 23 Next—Accesses the next value stored in data log memory. The operation of this key is similar to that of the Prev ke

24 Operation www.ets-lindgren.com CHARGING PROCEDURE 1. Plug the charger into a suitable AC source. 2. Make sure power to the readout is OFF. Inser

www.ets-lindgren.com Warranty 25 Appendix A: Warranty See the Product Information Bulletin included with your shipment for the complete ETS-Lindgr

26 Warranty www.ets-lindgren.com This page intentionally left blank.

www.ets-lindgren.com Communication Error Codes 27 Appendix B: Communication Error Codes When the HI-4416 detects an error condition during communic

28 Communication Error Codes www.ets-lindgren.com This page intentionally left blank.

www.ets-lindgren.com HI-4416 Operating Protocols 29 Appendix C: HI-4416 Operating Protocols Communication between the probe and the HI-4416 System

www.ets-lindgren.com iii Revision Description Date H Revised to current style standards May, 2013 J Updated part numbers in Replacement and Optional

30 HI-4416 Operating Protocols www.ets-lindgren.com VALID UNIT TYPES The following table lists the unit codes that can be sent in the data string an

www.ets-lindgren.com 491198-36 Battery Fast Charger 31 Appendix D: 491198-36 Battery Fast Charger The HI-4416 System Readout contains a Nickel-Cad

32 491198-36 Battery Fast Charger www.ets-lindgren.com SPECIFICATIONS NiCd Battery 3.6 Volt 3 Cell NiCd Battery, 1400 mAH (Rapid charge cells, 1.2

www.ets-lindgren.com 491198-36 Battery Fast Charger 33 POWER CABLE This charger is shipped with a three-wire power cable. When this cable is connect

34 491198-36 Battery Fast Charger www.ets-lindgren.com MAINTENANCE User serviceable parts do not exist inside the battery charger. Warranty may be

www.ets-lindgren.com 491198-36 Battery Fast Charger 35 If a fuse has blown, it must be replaced with the same type and value or an unsafe condition

36 491198-36 Battery Fast Charger www.ets-lindgren.com This page intentionally left blank.

www.ets-lindgren.com EC Declaration of Conformity 37 Appendix E: EC Declaration of Conformity The EC Declaration of Conformity is the method by whi

38 EC Declaration of Conformity www.ets-lindgren.com AUTHORIZED SIGNATORIES The authorizing signatures on the EC Declaration of Conformity document

iv www.ets-lindgren.com Table of Contents Notes, Cautions, and Warnings ... vii General Safety Considerat

www.ets-lindgren.com v Introduction ... 31 Specifications

vi www.ets-lindgren.com This page intentionally left blank.

www.ets-lindgren.com vii Notes, Cautions, and Warnings Note: Denotes helpful information intended to provide tips for better use of the product. Ca

viii www.ets-lindgren.com This page intentionally left blank.

www.ets-lindgren.com Introduction 9 1.0 Introduction The ETS-Lindgren HI-4000 Hazard Measurement System introduces fiber optic technology for the a